Bad link on Arduino_GigaDisplayTouch web page
On this page: Arduino_GigaDisplayTouch | Arduino Documentation clicking on the api button, brings you to a non-existent page. Arduino: Page Not found | Arduino Documentation 1 post - 1 participant...
View ArticleMore info links in board packages
The 'More info' links in board packages seem to now link to the main arduino.cc page rather the repository of the specific board package in question. Is this a recent change? The link in the...
View ArticleHelp needed to display external RTC date and time on DWIN display using ESP32
Hello everyone, I am a university student working on a project using an ESP32, DWIN display, MAX6675 temperature sensor, and an external RTC module to make a temperature recorder. I am facing a...
View ArticleArudino WIFI 1010 goes offline a lot
Hi I have four Arduino 1010 deployed now. I bought two first and these two work well up time is ~99%. Then I bought another two and these two have up time ~15%. They are running same sketch (just copy...
View ArticleUbuntu 24.04 on uno-q?
Hi, I have some potential project in mind with a cascaded ROS2 architecture with a Ventuno-Q as central node and a couple of UNO-Qs added for some tasks. Installing ROS2 on the Ventuno-Q is simple...
View ArticleM2 slot - what can I put there?
Hi, I was happy for just a very short time that I would have a use for the Samsung 970EVO Plus NVMe M.2 1TB SSD I had lying around for some time, but it simply does not fit because it is way too large...
View ArticleFloat32(big endian)
Hi Got stuck trying to get voltage data from this power meter :https://dariancabot.com/wp-content/uploads/2024/08/Eastron-SDM120-Modbus-protocol-V2.1.pdf. As you can see it uses 2x16 bit registers to...
View ArticleC++ Standard Library std::chrono::steady_clock has a wrong implementation
C++ Standard, see https://en.cppreference.com/cpp/chrono/steady_clock: Class std::chrono::steady_clock represents a monotonic clock. The time points of this clock cannot decrease as physical time...
View ArticleClik here to view.
TinyUSB Arduino
github.com GitHub - controllercustom/TinyUSB_Arduino: Arduino Library for TinyUSB, all classes, host and... Arduino Library for TinyUSB, all classes, host and device TinyUSB with a thin layer of...
View ArticleBHI260AP (Nicla Sense ME) on Zephyr: SPI reads all-zeros — silent CS skip for...
Spent a full day on this and the failure mode produces zero diagnostics, so leaving it here for the next person. Symptom: every BHY2 register read returns 0x00, bhy2_soft_reset / bhy2_boot_from_flash...
View ArticleClik here to view.
How can I contact Arduino?
Hello, I cannot enter a support request. I'm still getting this response: Is there any other way to contact Arduino? I have some problem with my order and sending a mail resulted in reply that the...
View ArticleCan Arduino VENTUNO Q support Arducam IMX519 or other manual-control MIPI CSI...
Hi Arduino team/community, I recently got an Arduino VENTUNO Q and want to understand what is possible for MIPI CSI camera support. My current project uses an Arducam IMX519 camera on a...
View ArticleESP-12 NodeMCU: Serial Monitor gibberish before Serial.begin()
I have an ESP-12 / ESP8266 / NodeMCU that "works" except for a start-of-sketch Serial barf. I have been reading the Forum about this topic, but find no resolution if "all the settings are correct."...
View ArticleClik here to view.
IDE 2.3.10 Serial Monitor window jitter
If the Serial Monitor window is "over full" vertically, AND I scroll (mouse, trackpad or arrow key) the Serial Monitor output window "up" so the "bottom" of the data shows WHILE the "top" of the...
View ArticleVideo card problem
Hi everyone, I just bought Ventuno Q. The problem is that something wrong with video. Even before system start booting but screen is power up, it starting blinking and have glitches. Please see a...
View ArticleClik here to view.
Can't get rid of "New (1)" on homepage
Since a few days; and to make it easier to debug () this does not happen always. The home page of the forum shows Clicking "New (1)" gives I can get rid of "New (1)" in the latter image with...
View ArticleUNO Q: Arduino Sketch using Zephyr C APIs fails to acquire ADC0 data of...
I am trying to learn Zephyr C API programming on the UNO Q board for the ADC Module. However, the code below fails during hardware initialisation with the message ADC hardware is not ready!. Could...
View ArticleIDE not opening properly - done everything it seems!
My IDE has suddenly stopped opening properly after a good month or two of perfectly normal use. Most of the UI is there, but almost everything is unresponsive and large black boxes take up the screen...
View ArticleClik here to view.
Help with rotary positioning
I am working on a project modifying a rebar bender to display and limit the angle of bending of the material that is getting bent. The machine works via an electric motor that drives a gearbox that...
View ArticleClik here to view.
Is this right for indoor weather station?
Hii i just wanted to ask for advice before i start spending hours on coding this little project. I want to build my own indoor temperature/humidity and air pressure station but using two Arduino...
View Article
